ansys接触分析，提示”创建的目标面是不连续的，有刚体也有变形

ychq123

程序 /PREP7   ET,1,SOLID186    MPTEMP,,,,,,,,              !钛 MPTEMP,1,0   MPDATA,EX,1,,1.15e11 MPDATA,PRXY,1,,0.37 MPTEMP,,,,,,,,   MPTEMP,1,0   MPDATA,DENS,1,,4.5e3 MPTEMP,,,,,,,,   MPTEMP,1,0   MPDATA,MU,1,,0.05 TB,BISO,1,1,2,               !双线性等向强化材料模型 TBTEMP,0 TBDATA,1,1000E6,4.2E10,,,,          MPTEMP,,,,,,,,              !金刚石 MPTEMP,1,0   MPDATA,EX,2,,1.1e12    MPDATA,PRXY,2,,0.07   MPTEMP,,,,,,,,   MPTEMP,1,0   MPDATA,DENS,2,,3.52e3 /PNUM,AREA,1 /PNUM,VOLU,1 CYLIND,0.5e-3,0,0,0.6e-3,0,90,    /ANG,1,30,YS,1   /REP,FAST    /ANG,1,30,YS,1   /REP,FAST    /ANG,1,30,YS,1   /REP,FAST    CYLIND,0.28e-3,0,0,0.2e-3,0,90,    VSBV,       1,       2   CONE,0.28e-3,0.3e-3,0.2e-3,0.3923e-3,0,90,    VSBV,       3,       1   CONE,0.3e-3,0.4e-3,0.3923e-3,0.6e-3,0,90, VSBV,       2,       1 CYLIND,0.28e-3,0,-0.5e-3,0.2e-3,0,90,   CONE,0.28e-3,0.3e-3,0.2e-3,0.3923e-3,0,90,    CONE,0.3e-3,0.3e-3,0.3923e-3,1e-3,0,90, VADD,1,2,4   SMRT,4 VSEL, , , ,       3 VSWEEP,3 VSEL, , , ,       5   VSWEEP,5 R,3,,,0.1 ET,2,TARGE170 ET,3,CONTA174 ASEL,S,,,8            !创建目标面 ASEL,A,,,10 ASEL,A,,,13 REAL,3 MAT,2 TYPE,2 NSLA,S,1 ESLN,S,0 ESURF ALLSEL,ALL ASEL,S,,,4            !创建接触面 ASEL,A,,,24 ASEL,A,,,27 REAL,3 MAT,1 TYPE,3 NSLA,S,1 ESLN,S,0 ESURF ALLSEL,ALL EPLOT REAL,3             !创建目标面的控制点 MAT,2    TYPE,2   KPLOT    KMESH,       9   ALLSEL,ALL eplot FINISH /SOLU DA,16,SYMM DA,17,SYMM DA,5,SYMM DA,6,SYMM DA,25,SYMM DA,26,SYMM DA,28,SYMM DA,29,SYMM ANTYPE,4 TRNOPT,FULL tintp,,0.25,0.5,0.5 outpr,all,all OUTRES,ALL,ALL AUTOTS,ON pred,on LNSRCH,on KBC,1 nlgeom,on ff=20945 pi=3.1415926 t=1/ff n=30 *do,i,1,n*20 time,t/n*i degree=sqrt(2)*5/180*3.1415926*sin(2*pi*ff*t/n*i) zong=sqrt(2)*(70e-9)*sin(2*pi*ff*t/n*i) DK,9,rotz,degree DK,9,uz,zong allsel,all da,1,uz,-1.5873e-5 allsel,all allsel nsubt，10,10000,1 solve *enddo   finish