03-01.dat
----------------------------------------------------------------------
TITLE = "EXAMPLE: 3D GEOMETRIES"
VARIABLES = "X", "Y", "Z"
ZONE T="Floor", I=3, J=3, F=POINT
0. 0. 0.
5. 0. 0.
10. 0. 0.
0. 5. 0.
5. 5. 0.
10. 5. 0.
0. 10. 0.
5. 10. 0.
10. 10. 0.
ZONE T="Ceiling", I=3, J=3, F=POINT
0. 0. 10.
5. 0. 10.
10. 0. 10.
0. 5. 10.
5. 5. 10.
10. 5. 10.
0. 10. 10.
5. 10. 10.
10. 10. 10.
|********************************************************************
* 导入03-01.dat数据文件后,选点左边工具栏目里的"3D"按纽,再选下面的"Scatter".
* 03-01.jpg
*********************************************************************
03-02.dat
----------------------------------------------------------------------
TITLE = "EXAMPLE: 3D GEOMETRIES"
VARIABLES = "X", "Y", "Z"
ZONE T="Floor", I=3, J=3, F=POINT
0. 0. 0.
5. 0. 0.
10. 0. 0.
0. 5. 0.
5. 5. 0.
10. 5. 0.
0. 10. 0.
5. 10. 0.
10. 10. 0.
ZONE T="Ceiling", I=3, J=3, F=POINT
0. 0. 10.
5. 0. 10.
10. 0. 10.
0. 5. 10.
5. 5. 10.
10. 5. 10.
0. 10. 10.
5. 10. 10.
10. 10. 10.
geometry X=0, Y=0, Z=0, M=GRID, C=BLUE, T=LINE3D, F=POINT, AAT=BOTH,
AST=PLAIN, ASZ=.01
1
12
10. 4.0 10.
9.5 5.0 10.0
9.3 4.0 9.0
10. 5.0 9.5
9.2 4.0 8.2
8.8 5.3 7.6
7.8 5.6 7.0
7.2 5.2 5.0
6.9 6.0 5.5
6.9 4.5 6.4
7.3 4.6 6.8
8.2 4.8 7.0
|********************************************************************
* 选点左边工具栏目里的"3D"按纽,发现多了一条空间折线,
* 再选下面的旋转按纽,用鼠标在图上旋转看看. 03-02.jpg
*(问题:导出成.bmp图像时,空间折线显示不完全,不知道是怎么回事情,估计是tecplot9
的问题.)
*********************************************************************
03-03.dat
----------------------------------------------------------------------
TITLE = "EXAMPLE: 3D GEOMETRIES"
VARIABLES = "X", "Y", "Z"
ZONE T="Floor", I=3, J=3, F=POINT
0. 0. 0.
5. 0. 0.
10. 0. 0.
0. 5. 0.
5. 5. 0.
10. 5. 0.
0. 10. 0.
5. 10. 0.
10. 10. 0.
ZONE T="Ceiling", I=3, J=3, F=POINT
0. 0. 10.
5. 0. 10.
10. 0. 10.
0. 5. 10.
5. 5. 10.
10. 5. 10.
0. 10. 10.
5. 10. 10.
10. 10. 10.
GEOMETRY X=0, Y=0, Z=0, M=GRID, C=BLUE, T=LINE3D, F=POINT, AAT=BOTH,
AST=PLAIN, ASZ=.01
1
12
10. 4.0 10.
9.5 5.0 10.0
9.3 4.0 9.0
10. 5.0 9.5
9.2 4.0 8.2
8.8 5.3 7.6
7.8 5.6 7.0
7.2 5.2 5.0
6.9 6.0 5.5
6.9 4.5 6.4
7.3 4.6 6.8
8.2 4.8 7.0
GEOMETRY X=0, Y=0, Z=0, M=GRID, C=RED, T=LINE3D, F=BLOCK
1
20
0 .1 .5 .7 1. 2. 4.9 6.3 6.5 6.6 6.9 8. 8.5 9. 10. 10. 10. 9.5 8.
9.
0 .1 .3 .4 .5 .7 .8 1. 2. 3. 3.5 3.7 4. 4. 4. 4. 4.5 5. 5.
6.
0 .1 .3 1. 3. 5. 6. 8. 10. 10. 10. 9. 7. 5. 2. 1. 0. 0. 0.
3.
|********************************************************************
* 选点左边工具栏目里的"3D"按纽,发现多了两条空间折线,
* 再选下面的旋转按纽,用鼠标在图上旋转看看. 03-03.jpg
*(问题:导出成.bmp图像时,空间折线显示不完全,不知道是怎么回事情,估计是tecplot9
的问题.)
*********************************************************************
几点说明:
----------------------------------------------------------------------
GEOMETRY X=0, Y=0, Z=0, M=GRID, C=BLUE, T=LINE3D, F=POINT, AAT=BOTH, AST=PLA
IN, ASZ=.01
(坐标原点平移位置) (颜色) (点) (不知道是什么意思
,但是可以缺省)
1 (这个1不知道是什么意思,但是不能缺少)
12 (空间点的数目)
|********************************************************************
* 大部分是可以缺省的,geometry一句可以用下面这句来代替.(颜色缺省是黑色)
* GEOMETRY T=LINE3D
*********************************************************************
思考题目:
复杂的空间曲线显示题目.
例子: Tec90\Example\dat\3dgeom.dat |